3M Matic model 19000 carton sealers and tapers
-Top and bottom tape heads
-Automatic adjustment for different box sizes
-With 2 side feed belts
-1/6 PH, 1 phase, 60 cycles, 110 volts motor
-Serial no.1727

3M Model 800R/3 Random Top and Bottom Case Taper
- Type 40800, serial#50082, built 2014
- Side belts
- Top and bottom tape heads
- Roller bar infeed and discharge conveyors
- 115 volts
- Width: 4.25" to 19.5", Heights: 4.75" x 19.5": lengths 8" or longer

3M Top and Bottom Case Taper
- Model A70 type 10700, Serial#50127 built 2011
- Bottom belts
- Casters
- 115 volts
- Up to 30 cases/minute
- Length: 6" to no limit
- Width: 6" to 21.5"
- Height: 4.75" to 21.5"
- Weight: 5 to 65 lbs

3M Top and Bottom Case Taper
- Model A70 type 10700, Serial#50059 built 2009
- Bottom belts
- Casters
- 115 volts
- Up to 30 cases/minute
- Length: 6" to no limit
- Width: 6" to 21.5"
- Height: 4.75" to 21.5"
- Weight: 5 to 65 lbs

3M Top and Bottom Case Taper
- Model A70 type 10700, Serial#50555 built 2009
- Bottom belts
- Casters
- 115 volts
- Up to 30 cases/minute
- Length: 6" to no limit
- Width: 6" to 21.5"
- Height: 4.75" to 21.5"
- Weight: 5 to 65 lbs

3M Top and Bottom Case Taper
- Model A70 type 10700, Serial#50125 built 2009
- Bottom belts
- Casters
- 115 volts
- Up to 30 cases/minute
- Length: 6" to no limit
- Width: 6" to 21.5"
- Height: 4.75" to 21.5"
- Weight: 5 to 65 lbs

3M model 17800 case sealer and tapers
- Top and bottom pressure sensitive
- Manual adjustment for different boxes sizes
- With 2 bottom feed belts
- 1/4 PH, 1 phase, 60 cycles, 110 volts motor

50 cuft Stainless Steel Double Ribbon Blender
- 75 cuft full capacity and approximately 50 cuft working capacity
- Stainless steel bowl and ribbon
- Inside dimensions approximately 80" x 39.5" x 41" deep
- Bottom end discharge with air-operated discharge valve (about 6" from floor)
- 3 piece cover
- 25 HP, 3 phase, 60 cycle, 230/460 volt motor

62-gallon Stainless Steel Tank :
- 22 1/2" diameter x 36 1/2" deep measurements tank
- Jacketed
- 1 3/8" diameter bottom center discharge
- with Cover

66" long x 4" dia. screw conveyor
- Stainless steel
- 24" dia x 18" deep hopper
- 3 phase, 60 cycles, 250/440 volts

80 Cu Ft stainless steel double ribbon blender
- Interior: 119” long x 42” wide x 48" deep
- Covers
- Tilt discharge
- Mounted on base
- 20 HP motor

9-ft long x 57" wide Stainless Steel Cooling Table
- 35" tall table on adjustable legs
- Plate coil
- Casters

AB Process 150 Gallon SS jacketed and Mixing Kettle
- Scrapered anchor agitator
- 42" diameter x 24" straight wall side
- Dual hinged covers on stainless steel skid
- Reglopes hot water heater for jacket
- Piping
- Bottom center outlet

ABC model 212-T Case Erector with Side Taper
- Serial#23916 built 2013
- Side taper seals the bottom of the carton
- Size range: 4-1/8" H x 5-3/4" W x 7" L up to 18" H x 16" W x 22-3/4" L (see pdf for carton drawing explaining the dimensions)
- Rated up to 15 cases/minute
- 240 volts at 9 amps
- Overall dimensions: 12ft 7" long x 4-ft wide x 66" tall

ACCOFIL MODEL FC POWDER FILLER
ACCOFILL MODEL FC SERIAL NUMBER 1289 POWDER FILLER, FOR VACCUM, DIMENSIONS OF MACHINE 19" LONG X 19" WIDTH X 39" HEIGHT

ACCOFIL MODEL FC POWDER FILLER
ACCOFILL MODEL FC SERIAL NUMBER 1289 POWDER FILLER, FOR VACCUM, DIMENSIONS OF MACHINE 19" LONG X 19" WIDTH X 39" HEIGHT

ALLIANCE SINGLE STATION PLUGGER
ALLIANCE PLUG INSERTER/PRESS, SET FOR APPROX. 2" DIAMETER SNAP IN CAP, SINGLE STATION, MOORE-FEED MODEL 7630 VIBRATORY BOWL FEEDER, AIR OPERATED CONTAINER GRIPPER ARMS, A.B. MODEL SLC 500 CONTROLLER WITH PANEL DISPLAY (MISSING CPU BOARD), SINGLE PHASE, 60

ALSOP STAINLESS STEEL PLATES
ALSOP 8-1/2" DIA. X 15" HI. FILTER PRESS STAINLESS STEEL PLATES, 1/2" DIAMETER INLET, 1/4" DIAMETER OUTLET, WITH CENTRIFUGAL PUMP, 1/2 HP, 110/220 V, 1 PH.

AMFEC Model 510 500 LB Paddle Mixer
- Stainless steel
- Variable pitch paddles
- Mix & reverse mix
- Mechanical toggle lock discharge doors
- Full split grating with safety switch
- Tub dimensions: 41” (L) x 30.5” (W) x 25” (H)
- Exterior dimensions: 80” (L) x 44” (W) x 56” (H)
- Discharge height: 30”
- Adjustable leveling feet
- Maximum bulk density: 90 Cu Ft @ 55 lbs/Cu Ft
- 4 HP, 3 phase, 60 cycles, 220 volt motor
- Serial #1814244

APV 16" Servo Driven Wire-Cut and Continuous Rope Extruder with Guillotine Cutter
- Built new in 2010
- Originally designed to cut pucks of cookies onto wax paper sheets
- All servo driven
- Allen Bradley controls w Touchscreen
- 16" wide two roll extruder
- Wire-cut with oscillating knife
- Continuous extrusion capable for ropes
- Paper feed roller for cutting products onto wax paper
- Guillotine cutter for wax paper but can also be used to cut ropes of product to specific lengths
- Raising and lowering bed
- Die with (5) outlets measuring approximately 0.625" x 1.25"
- 3/60/480v
- Machine on casters
- Footprint approximately 11' long x 4' wide