Selmi Top EX Tempering Unit
- Built new 2018
- Serial number 2042
- Tank capacity 60kg
- Tempers 60kg in 14 minutes
- Tempers 200kg/hr
- 3/50/220-380v 16 AMPS

Selmi Top EX Tempering Unit
- Built new 2018
- Serial number 1057
- Tank capacity 60kg
- Tempers 60kg in 14 minutes
- Tempers 200kg/hr
- 3/50/220-380v 16 AMPS

Selmi Tuttuno 4 One Shot Depositor
- Built new in 2018
- Serial number 122
- Up to 90 molds/hour
- 3/60/220v

Signode Little David case erector & Magnum case taper
- Signode Little David model CF-5 semi-automatic case erector
- Allen Bradley Micro800 PLC
- On casters
- 1 phase, 60 cycles, 115 volts
- Up to 6 cases/minute
- Length range: 6" -26.5"
- Width range: 5" – 20"
Highlight Magnum model 4500 top 7 bottom case taper
- 2 settings: Random & Memory
- 2" tape heads
- Air operated side belts
- On casters
- Up to 20 cases/minute

Smith 26" wide x 12-ft long Stainless Steel Cooling Tunnel
- (1) Fan/coil unit (freon compressor not included - stayed with building)
- 17.5" long infeed section and 12" discharge section
- No control panel (panel was built into another Smith tunnel sold separately)
- Belt tracker

Sollich 42" Inclusion Feeder
- Stainless Steel Hopper
- 42.5" wide belt width (35.5" between the nylon guides)
- ½ HP, 3 phase, 60 cycle, 480 volt motor

Sollich 620 (24") Caramel Nut Cluster Depositing Line - 150 clusters/minute
- Sollich KGM-M 620 mm (10) Piston Chocolate Depositor
Serial#9041001 built 2007
(10) 1/2" diameter pistons on 2" centers
Stainless steel jacketed hopper 27" x 7" x 8" deep
3 phase, 60 cycle, 460 volts, 5 kva
- Sollich ND-600 Nut Dropper
(2) drums with 1.25" diameter clusters and (1) drum with 1" diameter clusters
Vibra vibratory Nut Feeder with 16" diameter x 17" deep hopper with 4" wide x 66" long channel vibrator feeder
- Egan 10-Piston Servo Caramel Depositor
Serial#11-1007 built 2011
(10) 9/16" diameter pistons
3 phase, 60 cycle, 460 volts
- Smith Stainless Steel 26" wide x 28-ft long (covered sections) Cooling Tunnel
(2) Fan/coil units with freon compressors (stayed with building)
HMI control Unit
Jacketed hopper 25" x 8" x 9" deep
- 55.5 ft long overall conveyor belt length (Chocolate depositor to end of Smith Cooling tunnel)
One continuous belt with belt tracker
This line deposited chocolate onto the belt as a base for the cluster, then deposits nuts and then liquid caramel. Patties are cooled in the cooling tunnel and then traveled through a Sollich enrobing line (which is available for sale with this line)
(2) Quartz heaters

Sollich Auger/Mixing Screw
- 12" diameter x 44" long auger
- Stainless Steel jacketed trough
- 2 HP, 3 phase, 60 cycle, 277/460 volt motor

Sollich TFD-150 120 kg/hr Turbo Mini Tempering Unit
- Serial#9041002 built 2007
- Integrated refrigeration unit
- 3 phase, 60 cycle, 480 volts, 4.5 KVA

Sollich TTS-620 24" wide Temperstatic Enrober with Sollich Thermo Flow 40-ft Cooling Tunnel
- Enrober model TTS-620 serial#9041006 built 2007
- 3 phase, 60 cycle, 480 volts, 13 kva
- Built in tempering screw
- Double curtain flow pan
- Blower with nozzle
- Detailer
Sollich Thermoflow LSK-620 mm (24") x 42-ft Long Cooling Tunnel
- Serial#9041007/009 built 2007
- 42-ft long covered section with 3-ft infeed
- Tunnel requires a water or glycol chiller to be supplied to the fan/coil unit
Pack-off conveyor 24" wide x 13-ft long

Tinsley Belt Polisher model # TDF-74P
:

This 74" belt polisher for a production output of 400 - 800 lbs./hour is constructed totally of stainless steel with a food grade polypropylene belt and sidewalls. Using a heated top scraper to return maximum of the chocolate from the belt surface back into the processed product.

Includes the following:
- Intralox Series 800 mat top belting with ribs, 76" wide, and complete with all necessary UHMWP carry-way support wear strips. Driven by a 3 HP motor, 1750 RPM, complete with the gearbox for a final output of 76 RPM, or a linear belt speed of up to 200-FPM max. Drive motor controlled via variable frequency speed controller for belt speed adjustment from 0 - 200 FPM. This will allow for excellent product tumble and uniform product polishing at its proper belt speed for the different products.

- The polishing liquid feed will be controlled by the solenoid rotating valve and through the spray nozzle manifold. The manifold will be hot water jacketed for good polishing liquid flow. The spray nozzles will be at approximately 15" centers, allowing a good & uniform product coating. This polisher will be equipped with 5 spray nozzles.

- A 5 gallon tank with piping and one pump for the polish & glazing feed will be included.

- To prevent product traveling with the belt, a retaining bar spaced about ¼" from the belt surface will scrape the product off the belt and drop it down to the other product area.

- An interior light will light up the product processing area for easy inspection during the processing.

- The air knife for cold air supply to cool & dry the product is designed to handle a typical 1700 CFM of cold air at 48 - 55 deg. F. External air chiller will be required. (Not included with machine.)

- An air / fume exhaust duct will be installed at the back side of the machine to remove any vapors from the polishing process. Air exhaust blower rated for 1700 CFM mounted on top of machine is included.

- Lexan front doors will allow for easy product access and inspection.

- Basic machine with PLC controls and wired for 480 Volts, 3 Ph., 60 Hz., with main disconnect

- Machine size and weight: 105" long x 76" deep x 86" height. Approximately 3,200 pounds total.

Tinsley Chocolate Melter, 100 - 20,000 lbs.
New chocolate tanks in sizes from 100 to 20,000 lbs. in either carbon or stainless steel with electric immersion heaters and thermostats for water jacket. Temperature gauges for water and chocolate. Agitators with motor voltage to suit customers’ requirements. Other sizes are available upon request. Tanks are quoted with electrical starter boxes with on/off controls.

New Tinsley Stock Chocolate Melting/Holding Tanks with 3/60/220v electricals:

100lb stainless steel bottom drive
300lb stainless steel bottom drive
500lb stainless steel top drive
1,000lb stainless steel top drive
2,000lb stainless steel top drive
3,000lb stainless steel top drive
4,000lb stainless steel top drive
5,000lb stainless steel top drive

New Tinsley Non-Stock Chocolate Melting/Holding Tanks Made per Order:

500lb carbon steel top drive
500lb stainless steel bottom drive
1,000lb carbon steel top drive
1,000lb carbon steel bottom drive
1,000lb stainless steel bottom drive
1,300lb stainless steel top drive
2,000lb carbon steel top drive
2,000lb carbon steel bottom drive
2,000lb stainless steel bottom drive
2,000lb stainless steel top drive low profile
3,000lb carbon steel top drive
5,000lb carbon steel top drive
5,000lb horizontal stainless steel
7,500lb carbon steel top drive
7,500lb stainless steel top drive
10,000lb carbon steel top drive
10,000lb stainless steel top drive
20,000lb stainless steel top drive

Options:

Sanitary fittings threaded onto NPT pipe
UL approval on electrical panel
Lid interlock addition per side
Day-Night electrical controls
Stack light for agitator
Stainless steel electrical panel for standard size box
Upgrade to 480v electricals/panel
Water circulation pump with piping for 220v
Water circulation pump with piping for 115v or 480v
VFD for agitator or chocolate pump
Allen Bradley VFD for agitator or chocolate pump
Additional 3kW heater for 1000lb, 2000lb or 3000lb tanks
Upgrade 3kW heater to 4kW heater on 1000lb, 2000lb or 3000lb tanks
Upgrade 3kW heater to 4kW heater on 4000lb or 5000lb tanks
Allen Bradley controllers
Replace hinged lid with fixed lid
Load cells with carbon steel mounts
Upgrade carbon steel load cell mounts to stainless steel
Load cells summing board
Upcharge for customizing tank dimensions
Upcharge for customizing location of stock tank inlets/outlets
Upcharge for tank insulation for 5000lb and smaller tanks is 20% of tank price
Chocolate pump 1.5" in/out with jacketed head

Tricor model 225 Temper Meter
- P/N: 150-100 Rev C, serial#0208
- Box of sample cups

VMI Rayneri model 331300P Turbotest Mixer -
- Speed control
- Single phase, 220 volts

WELDOTRON MODEL 6401 BAG SEALER
WELDOTRON MODEL 6401 L BAR SEALER, 20" LONG X 16" WIDTH SEALING AREA, WITH TEMPERATURE CONTROLS, 1Ph, 115V.

WELDOTRON MODEL 7020, 16" WIDTH X 9" HEIGHT OPENING SHRINK TUNNEL WITH 12 1/2" WIDTH X 38" ROLLER BAR CONVEYOR, TEMPERATURE AND SPEED CONTROLS, 1/8 HP, 180 VDC, 3 PH

Wahl Metering Pump
- Stainless steel
- Temperature controls
- Variable volume control

Woody 16" Stringer with Conveyor
- 15" wide Hopper mounted to swinging arms with holes at bottom of hopper
- 17" wide x 68" long belt conveyor, fixed speed
- Hopper can be removed and standard stringing pipe can be added